Ford Fiesta Manuals

Ford Fiesta: Supplemental Restraint System / Pinpoint Test - DTC: W. Diagnosis and Testing

Ford Fiesta 2014 - 2019 Service Manual / Body and Paint / Supplemental Restraint System / Pinpoint Test - DTC: W. Diagnosis and Testing

B1417:11 and B1417:93


Refer to Wiring Diagrams Cell 46 for schematic and connector information.

The RCM monitors the RH front impact severity sensor circuits for the following faults:

  • Open circuit
  • Short to voltage
  • Short to ground
  • Faulted RH front impact severity sensor

If a fault is detected, the RCM stores DTC B1417:11 or B1417:93 in memory and sends a message to the IPC to illuminate the airbag warning indicator.


  DTC Fault Trigger Conditions


  DTC Description Fault Trigger Conditions
B1417:11 Passenger Frontal Restraints Sensor: Circuit Short to Ground A fault is indicated when the RCM senses a short to ground on the RH front impact severity sensor feed circuit.
B1417:93 Passenger Frontal Restraints Sensor: No Operation A fault is indicated when the RCM senses a faulted RH front impact severity sensor, a short to voltage on the feed circuit or an open feed or return circuit.

Possible Causes

  • Wiring, terminals or connectors
  • RH front impact severity sensor
  • RCM

Visual Inspection and Diagnostic Pre-checks

  • Inspect for a damaged RH front impact severity sensor.
  • Inspect the RH front impact severity sensor mounting and orientation.
  • Inspect for damaged wiring harness(es).
  • Inspect for loose or damaged connectors.

PINPOINT TEST A: B1417:11 AND B1417:93
NOTE: Most faults are due to connector and/or wiring concerns. Carry out a thorough inspection and verification before proceeding with the pinpoint test.
NOTE: Only disconnect or reconnect SRS components when instructed to do so within a pinpoint test step. Failure to follow this instruction may result in incorrect diagnosis of the SRS .
NOTE: Always make sure the correct SRS component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar. Check the part number listed in the Ford parts catalog to make sure the correct component is being installed. If an incorrect SRS component is installed, Diagnostic Trouble Codes (DTCs) may set.
NOTE: Do not probe any impact sensor. The impact sensor cannot be tested using a multi-meter
NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
A1 RETRIEVE RCM (RESTRAINTS CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)
  •   WARNING: Before beginning any service procedure in this section, refer to Safety Warnings in section 100-00 General Information. Failure to follow this instruction may result in serious personal injury.
    REFER to: Pyrotechnic Device Health and Safety Precautions (100-00 General Information, Description and Operation).
  • Ignition ON.
  • Using a diagnostic scan tool, perform RCM self-test.

Was DTC B1417:11 or B1417:93 retrieved on-demand during self-test?
Yes This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-demand during self-test.
For DTC B1417:11, GO to A2
For DTC B1417:93, GO to A5
No This is an intermittent fault when present as a Continuous Memory Diagnostic Trouble Code (CMDTC) only. GO to A10

A2 CHECK THE RIGHT FRONTAL RESTRAINTS SENSOR DTC (DIAGNOSTIC TROUBLE CODE) FOR A FAULT STATUS CHANGE (SHORT TO GROUND INDICATED)

NOTE: This pinpoint test step attempts to change the fault reported by the RCM by inducing a different fault condition. If the reported fault changes, this indicates the RCM is functioning correctly and is not the source of the fault.

  • Ignition OFF.
  • Depower the SRS .
    REFER to: Supplemental Restraint System (SRS) Depowering and Repowering (501-20B Supplemental Restraint System, General Procedures).
  • Disconnect: RH Front Impact Severity Sensor C1466.
  • Repower the SRS . Do not prove out the SRS at this time.
    REFER to: Supplemental Restraint System (SRS) Depowering and Repowering (501-20B Supplemental Restraint System, General Procedures).
  • Ignition ON.
  • Using a diagnostic scan tool, perform RCM self-test.

Did the on-demand DTC change from B1417:11 to B1417:93?
Yes INSTALL a new RH front impact severity sensor.
REFER to: Front Impact Severity Sensor (501-20B Supplemental Restraint System, Removal and Installation).
GO to A11
No GO to A3

A3 CHECK THE RH (RIGHT-HAND) FRONT IMPACT SEVERITY SENSOR FEED CIRCUIT FOR A SHORT TO GROUND
  • Ignition OFF.
  • Depower the SRS .
    REFER to: Supplemental Restraint System (SRS) Depowering and Repowering (501-20B Supplemental Restraint System, General Procedures).
  • Disconnect RCM C310A and C310B .
  • Measure:
    Click to display connectors
    Positive Lead Measurement / Action Negative Lead
      C1466-1   Ground

Is the resistance greater than 10,000 ohms?
Yes GO to A4
No REPAIR the circuit.
Refer to Wiring Diagrams Cell 5 for schematic and connector information.
GO to A11

A4 CHECK FOR A SHORT BETWEEN RH (RIGHT-HAND) FRONT IMPACT SEVERITY SENSOR CIRCUITS
  • Measure:
    Click to display connectors
    Positive Lead Measurement / Action Negative Lead
      C1466-1   C1466-2

Is the resistance greater than 10,000 ohms?
Yes GO to A9
No REPAIR the circuits.
Refer to Wiring Diagrams Cell 5 for schematic and connector information.
GO to A11

A5 CHECK THE RH (RIGHT-HAND) FRONT IMPACT SEVERITY SENSOR AND RCM (RESTRAINTS CONTROL MODULE) CONNECTIONS (NO OPERATION INDICATED)
  • Ignition OFF.
  • Depower the SRS .
    REFER to: Supplemental Restraint System (SRS) Depowering and Repowering (501-20B Supplemental Restraint System, General Procedures).
  • Inspect the RH Front Impact Severity Sensor C1466 to make sure it is fully seated and locked. Seat and lock the connector as necessary.
  • Gain access to the RCM and inspect C310A and C310B to make sure they are fully seated and locked. Seat and lock the connector as necessary.
  • Repower the SRS . Do not prove out the SRS at this time.
    REFER to: Supplemental Restraint System (SRS) Depowering and Repowering (501-20B Supplemental Restraint System, General Procedures).
  • Ignition ON.
  • Using a diagnostic scan tool, perform RCM self-test.

Was DTC B1417:93 retrieved on-demand during self-test?
Yes GO to A6
No The fault has been corrected. GO to A11

A6 CHECK THE RH (RIGHT-HAND) FRONT IMPACT SEVERITY SENSOR FEED CIRCUIT FOR A SHORT TO VOLTAGE (NO OPERATION INDICATED)
  • Ignition OFF.
  • Depower the SRS .
    REFER to: Supplemental Restraint System (SRS) Depowering and Repowering (501-20B Supplemental Restraint System, General Procedures).
  • Disconnect: RH Front Impact Severity Sensor C1466.
  • Disconnect: RCM C310A and C310B.
  • Repower the SRS . Do not prove out the SRS at this time.
    REFER to: Supplemental Restraint System (SRS) Depowering and Repowering (501-20B Supplemental Restraint System, General Procedures).
  • Ignition ON.
  • Measure:
    Click to display connectors
    Positive Lead Measurement / Action Negative Lead
      C1466-1   Ground

Is any voltage present?
Yes REPAIR the circuit.
Refer to Wiring Diagrams Cell 5 for schematic and connector information.
GO to A11
No GO to A7

A7 CHECK THE RH (RIGHT-HAND) FRONT IMPACT SEVERITY SENSOR CIRCUITS FOR AN OPEN (NO OPERATION INDICATED)
  • Ignition OFF.
  • Depower the SRS .
    REFER to: Supplemental Restraint System (SRS) Depowering and Repowering (501-20B Supplemental Restraint System, General Procedures).
  • Measure:
    Click to display connectors
    Positive Lead Measurement / Action Negative Lead
      C310A-16   C1466-1
      C310A-15   C1466-2

Are the resistances less than 0.5 ohm?
Yes GO to A8
No REPAIR the circuit(s).
Refer to Wiring Diagrams Cell 5 for schematic and connector information.
GO to A11

A8 CHECK THE RIGHT FRONTAL RESTRAINTS SENSOR DTC (DIAGNOSTIC TROUBLE CODE) FOR A FAULT STATUS CHANGE (NO OPERATION INDICATED)

NOTE: This pinpoint test step attempts to change the fault reported by the RCM by inducing a different fault condition. If the reported fault changes, this indicates the RCM is functioning correctly and is not the source of the fault.

  • Connect: RCM C310A and C310B.
  • Connect a fused jumper wire as shown:
    Click to display connectors
    Lead 1 Measurement / Action Lead 2
      C1466-1   C1466-2
  • Repower the SRS . Do not prove out the SRS at this time.
    REFER to: Supplemental Restraint System (SRS) Depowering and Repowering (501-20B Supplemental Restraint System, General Procedures).
  • Ignition ON.
  • Using a diagnostic scan tool, perform RCM self-test.

Did the on-demand DTC change from B1417:93 to B1417:11?
Yes REMOVE the fused jumper wire and INSTALL a new RH front impact severity sensor.
REFER to: Front Impact Severity Sensor (501-20B Supplemental Restraint System, Removal and Installation).
GO to A11
No REMOVE the fused jumper wire and GO to A9

A9 CONFIRM THE RCM (RESTRAINTS CONTROL MODULE) FAULT

NOTE: Make sure all SRS components and the RCM electrical connectors are connected before carrying out the self-test. If not, Diagnostic Trouble Codes (DTCs) will be recorded.

  • Ignition OFF.
  • Depower the SRS .
    REFER to: Supplemental Restraint System (SRS) Depowering and Repowering (501-20B Supplemental Restraint System, General Procedures).
  • Prior to reconnecting any previously disconnected SRS component:
    • inspect connector(s) (including any inline connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
    • inspect wire harness for any damaged, pinched, cut or pierced wires.
    • inspect RCM C310A and C310B Connector Position Assurance (CPA) lever/lock for correct operation.
    • repair any concerns found.
      Refer to Wiring Diagrams Cell 5 for schematic and connector information.
  • Connect: RH Front Impact Severity Sensor C1466.
  • Connect: RCM C310A and C310B.
  • Repower the SRS . Do not prove out the SRS at this time.
    REFER to: Supplemental Restraint System (SRS) Depowering and Repowering (501-20B Supplemental Restraint System, General Procedures).
  • Ignition ON.
  • Using a diagnostic scan tool, perform RCM self-test.

Was the original DTC retrieved on-demand during self-test?
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new RCM .
REFER to: Restraints Control Module (RCM) (501-20B Supplemental Restraint System, Removal and Installation).
GO to A11
No In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. GO to A10

A10 CHECK FOR AN INTERMITTENT FAULT
  • Ignition OFF.
  • Depower the SRS .
    REFER to: Supplemental Restraint System (SRS) Depowering and Repowering (501-20B Supplemental Restraint System, General Procedures).
  • Disconnect: RH Front Impact Severity Sensor C1466.
  • Disconnect: RCM C310A and C310B.
  • Inspect:
    • harness and component connectors for loose or spread terminals and loose or frayed wire connections at terminals.
    • wire harness for any damage, pinched, cut or pierced wires.
    • RCM C310A and C310B Connector Position Assurance (CPA) lever/lock for correct operation.
    • repair any concerns found.
      Refer to Wiring Diagrams Cell 5 for schematic and connector information.
  • Connect: RH Front Impact Severity Sensor C1466.
  • Connect: RCM C310A and C310B.
  • Repower the SRS . Do not prove out the SRS at this time.
    REFER to: Supplemental Restraint System (SRS) Depowering and Repowering (501-20B Supplemental Restraint System, General Procedures).
  • Ignition ON.
  • Using a diagnostic scan tool, perform RCM self-test.

Was DTC B1417:11 or B1417:93 retrieved on-demand during the self-test?
Yes This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-demand during self-test.
For DTC B1417:11, GO to A2
For DTC B1417:93, GO to A5
No The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. GO to A11

A11 CHECK FOR ADDITIONAL SRS (SUPPLEMENTAL RESTRAINT SYSTEM) DIAGNOSTIC TROUBLE CODES (DTCS)

  WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.

  • Ignition OFF.
  • Reconnect all SRS components (if previously disconnected).
  • If previously directed to depower the SRS , repower the SRS . Do not prove out the SRS at this time.
    REFER to: Supplemental Restraint System (SRS) Depowering and Repowering (501-20B Supplemental Restraint System, General Procedures).
  • Ignition ON.
  • NOTE: When selecting Restraints from the Self Test menu, DTCs are retrieved from the RCM and OCSM . Using a diagnostic scan tool, perform Restraints self-test.

Are any RCM and/or OCSM Diagnostic Trouble Codes (DTCs) retrieved on-demand during self-test?
Yes Do not clear any Diagnostic Trouble Codes (DTCs) until all Diagnostic Trouble Codes (DTCs) have been resolved. DIAGNOSE and REPAIR the RCM and/or OCSM Diagnostic Trouble Codes (DTCs).
REFER to: Airbag Supplemental Restraint System (SRS) (501-20 Supplemental Restraint System) .
No CLEAR Continuous Memory Diagnostic Trouble Codes (CMDTCs) from all modules. PROVE OUT the SRS . The repair is complete. RETURN the vehicle to the customer.


    Pinpoint Test - DTC: V. Diagnosis and Testing

    B..

    Pinpoint Test - DTC: X. Diagnosis and Testing

    BXXXX:2B (any BXXXX DTC with a 2B failure type) Signal Cross Coupled Refer to Wiring Diagrams Cell 46 for schematic and connector information...

    Other information:

    Ford Fiesta 2014 - 2019 Service Manual: Clutch - System Operation and Component Description. Description and Operation


    System Operation How the clutch works Cross-sectional view of a single disc dry clutch Item Description A Clutch disengaged B Clutch engaged 1 Flywheel 2 Clutch disc 3 Pressure plate 4 Diaphragm spring 5 Transmission input shaft 6 Clutch cover 7 Crankshaft The..

    Ford Fiesta 2014 - 2019 Service Manual: Heating, Ventilation and Air Conditioning (HVAC) Control Module. Removal and Installation


    Removal NOTE: Removal steps in this procedure may contain installation details. Remove the instrument panel lower trim panel. Refer to: Instrument Panel Lower Trim Panel (501-12 Instrument Panel and Console, Removal and Installation). Remove the retainers and the HVAC control module. Disconnect the electrical connectors. ..

    Categories

    Front Strut and Spring Assembly. Removal and Installation

    Removal

    NOTE: Removal steps in this procedure may contain installation details.

    NOTE: This step is only necessary when installing a new component to the left-hand side.

    Remove the nuts and position aside the remote brake fluid reservoir.
    Torque: 62 lb.in (7 Nm) Remove the strut and spring assembly upper mount nuts.
    Torque: 22 lb.ft (30 Nm)

    read more

    Copyright © 2024 www.fofiesta7.com