Ford Fiesta Manuals

Ford Fiesta: Supplemental Restraint System / Pinpoint Test - DTC: CC. Diagnosis and Testing

Ford Fiesta 2014 - 2019 Service Manual / Body and Paint / Supplemental Restraint System / Pinpoint Test - DTC: CC. Diagnosis and Testing

U0155:00

Normal Operation and Fault Conditions

The RCM uses information contained in messages from the IPC sent on the HS-CAN .


  DTC Fault Trigger Conditions


  DTC Description Fault Trigger Conditions
U0155:00 Lost Communication with Instrument Panel Cluster (IPC) Control Module: No Sub Type Information This DTC sets if the RCM does not receive an expected message from the IPC .

Possible Causes

  • Network traffic
  • IPC
  • RCM

PINPOINT TEST A: U0155:00
NOTE: Most faults are due to connector and/or wiring concerns. Carry out a thorough inspection and verification before proceeding with the pinpoint test.
NOTE: Only disconnect or reconnect SRS components when instructed to do so within a pinpoint test step. Failure to follow this instruction may result in incorrect diagnosis of the SRS .
NOTE: Always make sure the correct SRS component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar. Check the part number listed in the Ford parts catalog to make sure the correct component is being installed. If an incorrect SRS component is installed, Diagnostic Trouble Codes (DTCs) may set.
NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
A1 CHECK THE COMMUNICATION NETWORK
  •   WARNING: Before beginning any service procedure in this section, refer to Safety Warnings in section 100-00 General Information. Failure to follow this instruction may result in serious personal injury.
    REFER to: Pyrotechnic Device Health and Safety Precautions (100-00 General Information, Description and Operation).
  • Ignition ON.
  • Using a diagnostic scan tool, carry out a network test.

Does the IPC pass the network test?
Yes GO to A2
No To diagnose no communication with the IPC ,
REFER to: Communications Network (418-00 Module Communications Network, Diagnosis and Testing).

A2 CHECK THE RCM (RESTRAINTS CONTROL MODULE) CONTINUOUS MEMORY DIAGNOSTIC TROUBLE CODES (CMDTCS)
  • Using a diagnostic scan tool, perform RCM self-test.
  • Using a diagnostic scan tool, clear RCM Diagnostic Trouble Codes (DTCs).
  • Wait 10 seconds.
  • Using a diagnostic scan tool, perform RCM self-test.

Is DTC U0155:00 retrieved again?
Yes GO to A3
No The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

A3 RETRIEVE THE RECORDED DIAGNOSTIC TROUBLE CODES (DTCS) FROM THE RCM (RESTRAINTS CONTROL MODULE) SELF-TEST
  • Check the recorded Diagnostic Trouble Codes (DTCs) from the RCM self-test.

Is DTC U3003:16 or U3003:17 recorded?
Yes
REFER to: Pinpoint Test - DTC: FF (501-20B Supplemental Restraint System, Diagnosis and Testing).
No GO to A4

A4 RETRIEVE THE RECORDED DIAGNOSTIC TROUBLE CODES (DTCS) FROM THE IPC (INSTRUMENT PANEL CLUSTER) SELF-TEST
  • Using a diagnostic scan tool, perform IPC self-test.
  • Check for recorded Diagnostic Trouble Codes (DTCs) from the IPC self-test.

Is DTC U3003:16 or U3003:17 recorded?
Yes
REFER to: Instrumentation, Message Center and Warning Chimes (413-01 Instrumentation, Message Center and Warning Chimes, Diagnosis and Testing).
No GO to A5

A5 CHECK FOR DTC (DIAGNOSTIC TROUBLE CODE) U0155:00 SET IN OTHER MODULES
  • Using a diagnostic scan tool, perform self-test for all modules.

Is DTC U0155:00 set in the BCM , ACM , or APIM (if equipped)?
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern,
   Click here to access Guided Routine (IPC).
No CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new RCM .
REFER to: Restraints Control Module (RCM) (501-20B Supplemental Restraint System, Removal and Installation).


    Pinpoint Test - DTC: BB. Diagnosis and Testing

    U..

    Pinpoint Test - DTC: DD. Diagnosis and Testing

    U0253:00 Normal Operation and Fault Conditions The RCM uses information contained in messages from the APIM sent on the HS-CAN .   DTC Fault Trigger Conditions   DTC Description Fault Trigger Conditions U0253:00 Lost Communication with Accessory Protocol Interface M..

    Other information:

    Ford Fiesta 2014 - 2019 Service Manual: Vehicle Specific Body Construction. Description and Operation


    For recommended metal repair guidelines and recommendations, refer to the following illustrations and: For additional information, refer to: Specifications (501-25 Body Repairs - General Information, Specifications). Steel Type Legend Item Steel Type Color 1 Mild Steel Yellow ..

    Ford Fiesta 2014 - 2019 Service Manual: Steering Wheel Multifunction Switch. Removal and Installation


    Removal NOTE: Removal steps in this procedure may contain installation details. Refer to: Driver Airbag (501-20B Supplemental Restraint System, Removal and Installation). Remove the screws. Using a suitable flat-bladed tool, remove the steering wheel bezel. Disco..

    Categories

    Parking Brake Control. Removal and Installation

    Removal

    NOTE: Removal steps in this procedure may contain installation details.

    Remove the floor console.
    Refer to: Floor Console (501-12 Instrument Panel and Console, Removal and Installation).
    Remove the driver seat.
    Refer to: Front Seat (501-10 Seating, Removal and Installation).
    Remove the parking brake cable adjustment lock nut.
    Loosen the parking brake cable adjustment nut.

    read more

    Copyright © 2024 www.fofiesta7.com