Ford Fiesta Manuals

Ford Fiesta: Information and Entertainment System - General Information - Vehicles With: AM/FM/CD/SYNC / Reset the SYNC Module [APIM]. General Procedures

Programming

NOTE: An APIM Reset consists of a battery disconnect and a SYNC® system Master Reset. It may not be necessary to perform a Master Reset after disconnecting the battery if the concern is resolved.

NOTE: This procedure clears all Continuous Memory Diagnostic Trouble Codes (CMDTCs). The Diagnostic Trouble Codes (DTCs) must be recorded now if other non-SYNC® diagnoses are to be performed after this procedure.

  1. Remove any devices connected to the USB port(s), audio input jack/socket (if equipped), SD slot (if equipped), or RCA jacks (if equipped).
  1. Disconnect the negative battery cable for 1 minute, then reconnect it.
    Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
  1. NOTE: Performing a Master Reset returns all preference settings to the factory defaults, erases the phone book and call histories, and deletes any Bluetooth devices paired with the SYNC® system. For vehicles with navigation, the customer’s saved destinations (home, favorites, and previous) are erased. For vehicles with a TCU , any devices paired with the MyFord® Mobile or MyLincoln Mobile™ phone application will be deleted.

    Perform a Master Reset. If necessary, refer to “Master Reset” in the Owner's Literature.
  1. Verify system function using the MIT 105-00120 to test the audio output for the USB port(s), audio input jack/socket (if equipped), and Bluetooth. If equipped, test the audio output for the RCA jacks using RCA Adapter 105-00121.
  1. NOTE: If the concern remains after completing the APIM Reset procedure, advise the customer to power their device off and back on for a simple reboot. In some cases, if possible, the device's battery may also need to be removed and re-installed to complete a reboot. Delete SYNC® from the device’s Bluetooth menu prior to re-pairing the phone to the SYNC® system. If necessary, the customer can also perform a Master Clear, Master Reset, or Factory Data Reset on their device following the manufacturer's instructions in the device's owner's manual and/or website. Customer devices may affect the operation of SYNC® and this should be understood to prevent unnecessary diagnosis or repairs to the system.

    If a concern is still present, return to the Symptom Charts.

    Information and Entertainment System. Diagnosis and Testing

    ..

    SYNC Module [APIM] Programming. General Procedures

    Special Tool(s) / General Equipment SYNC USB 2.0 A Male to A Male Cable Activation   WARNING: Before beginning any service procedure in this section, refer to Health and Safety Precautions in section 100-00 General Information...

    Other information:

    Ford Fiesta 2014 - 2019 Service Manual: Evaporative Emissions. Diagnosis and Testing


    Engine Diagnostic Information Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. For information about these,REFER to: Diagnostic Methods (100-00 General Information, Description and Operation)...

    Ford Fiesta 2014 - 2019 Service Manual: Steering Column. Removal and Installation


    Special Tool(s) / General Equipment Grinder Removal NOTICE: To prevent damage to the clockspring, make sure the front wheels are in the straight-ahead position. NOTICE: Precise tolerances are required when manufacturing a steering column...

    Categories

    Brake Master Cylinder. Removal and Installation

    Removal

    NOTICE: If the fluid is spilled on the paintwork, the affected area must be immediately washed down with cold water.

    NOTE: Removal steps in this procedure may contain installation details.

    All vehicles

    Remove the battery tray.
    Refer to: Battery Tray - 1.6L Duratec-16V Ti-VCT (88kW/120PS) – Sigma (414-01 Battery, Mounting and Cables, Removal and Installation).
    Refer to: Battery Tray - 1.6L EcoBoost (132kW/180PS) – Sigma (414-01 Battery, Mounting and Cables, Removal and Installation).
    Disconnect the vacuum tube from the brake booster and detach the routing clip.

    read more

    Copyright © 2024 www.fofiesta7.com